Wall plug outlet change
.everyoneloves__top-leaderboard:empty,.everyoneloves__mid-leaderboard:empty,.everyoneloves__bot-mid-leaderboard:empty{ margin-bottom:0;
}
I am replacing a 3 prong wall plug outlet receptacle with a new one that also has USB ports built in. The old outlet had 2 black wires and 2 white wires attached and a ground wire. The New outlet has only one screw for black and one for white. Should i pigtail both blacks together and both whites together?
Thank you for your advice.
walls receptacle
asked 3 hours ago
kdh358kdh358
61
New contributor
kdh358 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I am replacing a 3 prong wall plug outlet receptacle with a new one that also has USB ports built in. The old outlet had 2 black wires and 2 white wires attached and a ground wire. The New outlet has only one screw for black and one for white. Should i pigtail both blacks together and both whites together?
Thank you for your advice.
walls receptacle
asked 3 hours ago
kdh358kdh358
61
New contributor
kdh358 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I am replacing a 3 prong wall plug outlet receptacle with a new one that also has USB ports built in. The old outlet had 2 black wires and 2 white wires attached and a ground wire. The New outlet has only one screw for black and one for white. Should i pigtail both blacks together and both whites together?
Thank you for your advice.
walls receptacle
asked 3 hours ago
kdh358kdh358
61
New contributor
kdh358 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I am replacing a 3 prong wall plug outlet receptacle with a new one that also has USB ports built in. The old outlet had 2 black wires and 2 white wires attached and a ground wire. The New outlet has only one screw for black and one for white. Should i pigtail both blacks together and both whites together?
Thank you for your advice.
walls receptacle
walls receptacle
asked 3 hours ago
kdh358kdh358
61
New contributor
kdh358 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 3 hours ago
kdh358kdh358
61
New contributor
kdh358 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 3 hours ago
kdh358kdh358
61
New contributor
kdh358 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 3 hours ago
kdh358kdh358
61
asked 3 hours ago
kdh358kdh358
61
61
New contributor
kdh358 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
kdh358 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
kdh358 is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
add a comment |
1 Answer
1
active
oldest
votes
Look at each side of the old outlet. There will be copper tabs connecting the two screws that can be broken off. If the tab is intact, then connect them together.
If the tab is broken, connect to only one of the wires and leave the other disconnected (put a wirenut on the wire. Make sure the nut is small enough to grab onto the wire securely). Make sure to use the wires from the same top or bottom of the outlet.
answered 1 hour ago
DoxyLoverDoxyLover
3,3041816
+1- adder: If the tab is intact and you connect them together, do so with a wire nut and a short pigtail to attach to the new receptacle; tucking the nuts and joined wires into the back of the box. Do not attach both directly to the terminal screw of the receptacle.
– Jimmy Fix-it
1 hour ago
It’s also possible the terminals on the new outlet are designed for either 1 or 2 wires to connect on the single terminal, but we’d need the model number or a picture to tell whether that is in fact true.
– Tyson
28 mins ago
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "73"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
kdh358 is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f162042%2fwall-plug-outlet-change%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
Look at each side of the old outlet. There will be copper tabs connecting the two screws that can be broken off. If the tab is intact, then connect them together.
If the tab is broken, connect to only one of the wires and leave the other disconnected (put a wirenut on the wire. Make sure the nut is small enough to grab onto the wire securely). Make sure to use the wires from the same top or bottom of the outlet.
answered 1 hour ago
DoxyLoverDoxyLover
3,3041816
+1- adder: If the tab is intact and you connect them together, do so with a wire nut and a short pigtail to attach to the new receptacle; tucking the nuts and joined wires into the back of the box. Do not attach both directly to the terminal screw of the receptacle.
– Jimmy Fix-it
1 hour ago
It’s also possible the terminals on the new outlet are designed for either 1 or 2 wires to connect on the single terminal, but we’d need the model number or a picture to tell whether that is in fact true.
– Tyson
28 mins ago
add a comment |
Look at each side of the old outlet. There will be copper tabs connecting the two screws that can be broken off. If the tab is intact, then connect them together.
If the tab is broken, connect to only one of the wires and leave the other disconnected (put a wirenut on the wire. Make sure the nut is small enough to grab onto the wire securely). Make sure to use the wires from the same top or bottom of the outlet.
answered 1 hour ago
DoxyLoverDoxyLover
3,3041816
+1- adder: If the tab is intact and you connect them together, do so with a wire nut and a short pigtail to attach to the new receptacle; tucking the nuts and joined wires into the back of the box. Do not attach both directly to the terminal screw of the receptacle.
– Jimmy Fix-it
1 hour ago
It’s also possible the terminals on the new outlet are designed for either 1 or 2 wires to connect on the single terminal, but we’d need the model number or a picture to tell whether that is in fact true.
– Tyson
28 mins ago
add a comment |
Look at each side of the old outlet. There will be copper tabs connecting the two screws that can be broken off. If the tab is intact, then connect them together.
If the tab is broken, connect to only one of the wires and leave the other disconnected (put a wirenut on the wire. Make sure the nut is small enough to grab onto the wire securely). Make sure to use the wires from the same top or bottom of the outlet.
answered 1 hour ago
DoxyLoverDoxyLover
3,3041816
Look at each side of the old outlet. There will be copper tabs connecting the two screws that can be broken off. If the tab is intact, then connect them together.
If the tab is broken, connect to only one of the wires and leave the other disconnected (put a wirenut on the wire. Make sure the nut is small enough to grab onto the wire securely). Make sure to use the wires from the same top or bottom of the outlet.
answered 1 hour ago
DoxyLoverDoxyLover
3,3041816
answered 1 hour ago
DoxyLoverDoxyLover
3,3041816
answered 1 hour ago
DoxyLoverDoxyLover
3,3041816
answered 1 hour ago
DoxyLoverDoxyLover
3,3041816
3,3041816
+1- adder: If the tab is intact and you connect them together, do so with a wire nut and a short pigtail to attach to the new receptacle; tucking the nuts and joined wires into the back of the box. Do not attach both directly to the terminal screw of the receptacle.
– Jimmy Fix-it
1 hour ago
It’s also possible the terminals on the new outlet are designed for either 1 or 2 wires to connect on the single terminal, but we’d need the model number or a picture to tell whether that is in fact true.
– Tyson
28 mins ago
add a comment |
+1- adder: If the tab is intact and you connect them together, do so with a wire nut and a short pigtail to attach to the new receptacle; tucking the nuts and joined wires into the back of the box. Do not attach both directly to the terminal screw of the receptacle.
– Jimmy Fix-it
1 hour ago
It’s also possible the terminals on the new outlet are designed for either 1 or 2 wires to connect on the single terminal, but we’d need the model number or a picture to tell whether that is in fact true.
– Tyson
28 mins ago
+1- adder: If the tab is intact and you connect them together, do so with a wire nut and a short pigtail to attach to the new receptacle; tucking the nuts and joined wires into the back of the box. Do not attach both directly to the terminal screw of the receptacle.
– Jimmy Fix-it
1 hour ago
+1- adder: If the tab is intact and you connect them together, do so with a wire nut and a short pigtail to attach to the new receptacle; tucking the nuts and joined wires into the back of the box. Do not attach both directly to the terminal screw of the receptacle.
– Jimmy Fix-it
1 hour ago
It’s also possible the terminals on the new outlet are designed for either 1 or 2 wires to connect on the single terminal, but we’d need the model number or a picture to tell whether that is in fact true.
– Tyson
28 mins ago
It’s also possible the terminals on the new outlet are designed for either 1 or 2 wires to connect on the single terminal, but we’d need the model number or a picture to tell whether that is in fact true.
– Tyson
28 mins ago
add a comment |
kdh358 is a new contributor. Be nice, and check out our Code of Conduct.
kdh358 is a new contributor. Be nice, and check out our Code of Conduct.
kdh358 is a new contributor. Be nice, and check out our Code of Conduct.
kdh358 is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Home Improvement Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f162042%2fwall-plug-outlet-change%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
