Issue with units for a rocket nozzle throat area problem
$begingroup$
I'm working through How to Design, Build, and Test Small Liquid-Fuel Rocket Engines. The guide explains calculating a rocket nozzle throat area using Eq. (7):
$$A_t = frac{w_t}{P_t} sqrt{frac{R T_t}{gamma g_c}} $$
where $w_t$ is flow measured in lb/s, $P_t$ is pressure measured in psi, $R$ is the specific gas constant for gaseous oxygen and hydrocarbon fuel which equals 65 ft-lb/lb R(rankine), $T_t$ is temperature of the chamber measured in rankine, $gamma$ being the ratio of gas specific heats, and the gravitational constant $g_c$ measured in ft/s².
My issue is for the worked out problem on the guide, they give an example here but the answer is in in² instead of ft². I'm not sure how they got inches instead of feet because they didn't do any kind of conversion that I can tell. I tried following the units to see how they got inches but I'm not sure. Shouldn't the answer be in feet, and if not how is it inches?
rockets nozzle rocket-equation
New contributor
$endgroup$
|
show 2 more comments
$begingroup$
I'm working through How to Design, Build, and Test Small Liquid-Fuel Rocket Engines. The guide explains calculating a rocket nozzle throat area using Eq. (7):
$$A_t = frac{w_t}{P_t} sqrt{frac{R T_t}{gamma g_c}} $$
where $w_t$ is flow measured in lb/s, $P_t$ is pressure measured in psi, $R$ is the specific gas constant for gaseous oxygen and hydrocarbon fuel which equals 65 ft-lb/lb R(rankine), $T_t$ is temperature of the chamber measured in rankine, $gamma$ being the ratio of gas specific heats, and the gravitational constant $g_c$ measured in ft/s².
My issue is for the worked out problem on the guide, they give an example here but the answer is in in² instead of ft². I'm not sure how they got inches instead of feet because they didn't do any kind of conversion that I can tell. I tried following the units to see how they got inches but I'm not sure. Shouldn't the answer be in feet, and if not how is it inches?
rockets nozzle rocket-equation
New contributor
$endgroup$
$begingroup$
You can learn more about MathJax for equations here. I removed therocketlab
tag; after reading that the address and original text was from circa 1967, it doesn't seem to be related to the same company that the tag refers to.
$endgroup$
– uhoh
yesterday
$begingroup$
This is really a no-good equation because it has pounds mass (in the flowrate) over pounds force (in the press) outside the radical. It should be the mass flowrate in every engineer's favorite unit, slugs/sec. See Sutton p. 61 pyrobin.com/files/Rocket%20Propulsion%20Elements.pdf
$endgroup$
– Organic Marble
yesterday
$begingroup$
@OrganicMarble Are the units for $R$ supposed to be ft-lbf / lbm R?
$endgroup$
– Russell Borogove
yesterday
$begingroup$
@RussellBorogove actually no. To be consistent it should be ft-lbf / slug R engineeringtoolbox.com/…
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
@OrganicMarble Same dimensions, at least.
$endgroup$
– Russell Borogove
yesterday
|
show 2 more comments
$begingroup$
I'm working through How to Design, Build, and Test Small Liquid-Fuel Rocket Engines. The guide explains calculating a rocket nozzle throat area using Eq. (7):
$$A_t = frac{w_t}{P_t} sqrt{frac{R T_t}{gamma g_c}} $$
where $w_t$ is flow measured in lb/s, $P_t$ is pressure measured in psi, $R$ is the specific gas constant for gaseous oxygen and hydrocarbon fuel which equals 65 ft-lb/lb R(rankine), $T_t$ is temperature of the chamber measured in rankine, $gamma$ being the ratio of gas specific heats, and the gravitational constant $g_c$ measured in ft/s².
My issue is for the worked out problem on the guide, they give an example here but the answer is in in² instead of ft². I'm not sure how they got inches instead of feet because they didn't do any kind of conversion that I can tell. I tried following the units to see how they got inches but I'm not sure. Shouldn't the answer be in feet, and if not how is it inches?
rockets nozzle rocket-equation
New contributor
$endgroup$
I'm working through How to Design, Build, and Test Small Liquid-Fuel Rocket Engines. The guide explains calculating a rocket nozzle throat area using Eq. (7):
$$A_t = frac{w_t}{P_t} sqrt{frac{R T_t}{gamma g_c}} $$
where $w_t$ is flow measured in lb/s, $P_t$ is pressure measured in psi, $R$ is the specific gas constant for gaseous oxygen and hydrocarbon fuel which equals 65 ft-lb/lb R(rankine), $T_t$ is temperature of the chamber measured in rankine, $gamma$ being the ratio of gas specific heats, and the gravitational constant $g_c$ measured in ft/s².
My issue is for the worked out problem on the guide, they give an example here but the answer is in in² instead of ft². I'm not sure how they got inches instead of feet because they didn't do any kind of conversion that I can tell. I tried following the units to see how they got inches but I'm not sure. Shouldn't the answer be in feet, and if not how is it inches?
rockets nozzle rocket-equation
rockets nozzle rocket-equation
New contributor
New contributor
edited yesterday
Russell Borogove
87k3291376
87k3291376
New contributor
asked yesterday
MAP3MAP3
282
282
New contributor
New contributor
$begingroup$
You can learn more about MathJax for equations here. I removed therocketlab
tag; after reading that the address and original text was from circa 1967, it doesn't seem to be related to the same company that the tag refers to.
$endgroup$
– uhoh
yesterday
$begingroup$
This is really a no-good equation because it has pounds mass (in the flowrate) over pounds force (in the press) outside the radical. It should be the mass flowrate in every engineer's favorite unit, slugs/sec. See Sutton p. 61 pyrobin.com/files/Rocket%20Propulsion%20Elements.pdf
$endgroup$
– Organic Marble
yesterday
$begingroup$
@OrganicMarble Are the units for $R$ supposed to be ft-lbf / lbm R?
$endgroup$
– Russell Borogove
yesterday
$begingroup$
@RussellBorogove actually no. To be consistent it should be ft-lbf / slug R engineeringtoolbox.com/…
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
@OrganicMarble Same dimensions, at least.
$endgroup$
– Russell Borogove
yesterday
|
show 2 more comments
$begingroup$
You can learn more about MathJax for equations here. I removed therocketlab
tag; after reading that the address and original text was from circa 1967, it doesn't seem to be related to the same company that the tag refers to.
$endgroup$
– uhoh
yesterday
$begingroup$
This is really a no-good equation because it has pounds mass (in the flowrate) over pounds force (in the press) outside the radical. It should be the mass flowrate in every engineer's favorite unit, slugs/sec. See Sutton p. 61 pyrobin.com/files/Rocket%20Propulsion%20Elements.pdf
$endgroup$
– Organic Marble
yesterday
$begingroup$
@OrganicMarble Are the units for $R$ supposed to be ft-lbf / lbm R?
$endgroup$
– Russell Borogove
yesterday
$begingroup$
@RussellBorogove actually no. To be consistent it should be ft-lbf / slug R engineeringtoolbox.com/…
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
@OrganicMarble Same dimensions, at least.
$endgroup$
– Russell Borogove
yesterday
$begingroup$
You can learn more about MathJax for equations here. I removed the
rocketlab
tag; after reading that the address and original text was from circa 1967, it doesn't seem to be related to the same company that the tag refers to.$endgroup$
– uhoh
yesterday
$begingroup$
You can learn more about MathJax for equations here. I removed the
rocketlab
tag; after reading that the address and original text was from circa 1967, it doesn't seem to be related to the same company that the tag refers to.$endgroup$
– uhoh
yesterday
$begingroup$
This is really a no-good equation because it has pounds mass (in the flowrate) over pounds force (in the press) outside the radical. It should be the mass flowrate in every engineer's favorite unit, slugs/sec. See Sutton p. 61 pyrobin.com/files/Rocket%20Propulsion%20Elements.pdf
$endgroup$
– Organic Marble
yesterday
$begingroup$
This is really a no-good equation because it has pounds mass (in the flowrate) over pounds force (in the press) outside the radical. It should be the mass flowrate in every engineer's favorite unit, slugs/sec. See Sutton p. 61 pyrobin.com/files/Rocket%20Propulsion%20Elements.pdf
$endgroup$
– Organic Marble
yesterday
$begingroup$
@OrganicMarble Are the units for $R$ supposed to be ft-lbf / lbm R?
$endgroup$
– Russell Borogove
yesterday
$begingroup$
@OrganicMarble Are the units for $R$ supposed to be ft-lbf / lbm R?
$endgroup$
– Russell Borogove
yesterday
$begingroup$
@RussellBorogove actually no. To be consistent it should be ft-lbf / slug R engineeringtoolbox.com/…
$endgroup$
– Organic Marble
yesterday
$begingroup$
@RussellBorogove actually no. To be consistent it should be ft-lbf / slug R engineeringtoolbox.com/…
$endgroup$
– Organic Marble
yesterday
1
1
$begingroup$
@OrganicMarble Same dimensions, at least.
$endgroup$
– Russell Borogove
yesterday
$begingroup$
@OrganicMarble Same dimensions, at least.
$endgroup$
– Russell Borogove
yesterday
|
show 2 more comments
2 Answers
2
active
oldest
votes
$begingroup$
$R$ and $g_c$ each have a foot component in their units; therefore the feet cancel out when $R$ is divided by $g_c$.
$P_t$ is in pounds per square inch; since you're dividing by that, it's effectively units of square inch per pound, which is where the square inches in the answer comes from.
The rest of the unit cancellation is confusing because of the use of pounds as both a unit of mass and a unit of force (weight). This thread on thespacerace.com discusses the different ways of presenting your equation; the money quote is here:
Outside the square root, my equation uses slugs for the mass flow rate, while the other equation uses pounds (i.e. weight). To convert pounds to slugs we must divide by gc outside the square root.
Inside the square root, my equation uses R' equal to 49,720 ft-lb/slug-R, while the other equation uses 1545.32 ft-lb/lb-R. To convert ft-lb/lb-R to ft-lb/slug-R we must multiple by gc inside the square root.
The combination of these two conversion factors is,
1/gc * (gc)^1/2 = 1/gc^1/2
therefore we end up with gc in the demoninator inside the square root.
$endgroup$
$begingroup$
Nice edit, I was just going ask about that unit on gamma....
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
Zing! Yeah, I misread the unit attribution.
$endgroup$
– Russell Borogove
yesterday
$begingroup$
It's not the right pounds though outside the radical. Bad equation! Bad! (Hits equation on nose with rolled up newspaper)
$endgroup$
– Organic Marble
yesterday
$begingroup$
Ugh, flowrate being mass rather than force? Maybe I'll delete everything except the inch/foot portion of my analysis, since this is way out of my wheelhouse.
$endgroup$
– Russell Borogove
yesterday
add a comment |
$begingroup$
That equation as you give it with the values you supply is a bad mish-mash of units. It's painful to do this in the English system, but gather your courage, we can get through it.
You must specify the flowrate in $frac{slugs}{sec}$. Yes, slugs, the real engineer's unit of massTM. A slug is 1 $frac {lbf - sec^2} {ft}$ and equates to ~ 32.2 lbm. So flowrate in $frac{slugs}{sec}$ has the units of $frac{lbf-sec}{ft}$.
You also must specify the pressure in $frac{lbf}{ft^2}$.
Dividing through you get outside the radical the units of $ft-sec$.
Inside the radical the gas constant is $frac{ft-lbf}{slug-R}$. The R cancels out with the temperature unit. gamma is dimensionless.
So if you substitute in $frac{lbf- sec^2}{ft}$ for the slug, you end up with $frac{ft^2}{sec^2}$ inside the radical.
Taking the square root, it's $frac{ft}{sec}$, then multiply by the $ft-sec$ outside the radical, to get $ft^2$.
Welcome to the world of Apollo and Shuttle rocket engine calculations.
$endgroup$
1
$begingroup$
I was caught in the transition, my books in college had both. Shuttle and Apollo were all English, ISS is metric. Either is OK if you are used to it but metric is a lot more intuitive.
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
Are you thinking the "-" is a minus sign? It's a hyphen. It's deplorable, I know, but that's the way these units are written. See the units on the gas constant in the question. "65 ft-lb/lb R(rankine)," and in the quote in the other answer "ft-lb/lb-R to ft-lb/slug-R"
$endgroup$
– Organic Marble
10 hours ago
1
$begingroup$
oh $frac{lbftext{-}sec^2}{ft}$ what the merry heck are hyphens doing in there? "english" units are ridiculous
$endgroup$
– JCRM
10 hours ago
1
$begingroup$
I cannot argue with that, lol
$endgroup$
– Organic Marble
10 hours ago
1
$begingroup$
I think that mathjax requires text to insert a hyphen says everything about how much they belong in formulae :D
$endgroup$
– JCRM
9 hours ago
|
show 7 more comments
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["$", "$"], ["\\(","\\)"]]);
});
});
}, "mathjax-editing");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "508"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
MAP3 is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fspace.stackexchange.com%2fquestions%2f34711%2fissue-with-units-for-a-rocket-nozzle-throat-area-problem%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
$R$ and $g_c$ each have a foot component in their units; therefore the feet cancel out when $R$ is divided by $g_c$.
$P_t$ is in pounds per square inch; since you're dividing by that, it's effectively units of square inch per pound, which is where the square inches in the answer comes from.
The rest of the unit cancellation is confusing because of the use of pounds as both a unit of mass and a unit of force (weight). This thread on thespacerace.com discusses the different ways of presenting your equation; the money quote is here:
Outside the square root, my equation uses slugs for the mass flow rate, while the other equation uses pounds (i.e. weight). To convert pounds to slugs we must divide by gc outside the square root.
Inside the square root, my equation uses R' equal to 49,720 ft-lb/slug-R, while the other equation uses 1545.32 ft-lb/lb-R. To convert ft-lb/lb-R to ft-lb/slug-R we must multiple by gc inside the square root.
The combination of these two conversion factors is,
1/gc * (gc)^1/2 = 1/gc^1/2
therefore we end up with gc in the demoninator inside the square root.
$endgroup$
$begingroup$
Nice edit, I was just going ask about that unit on gamma....
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
Zing! Yeah, I misread the unit attribution.
$endgroup$
– Russell Borogove
yesterday
$begingroup$
It's not the right pounds though outside the radical. Bad equation! Bad! (Hits equation on nose with rolled up newspaper)
$endgroup$
– Organic Marble
yesterday
$begingroup$
Ugh, flowrate being mass rather than force? Maybe I'll delete everything except the inch/foot portion of my analysis, since this is way out of my wheelhouse.
$endgroup$
– Russell Borogove
yesterday
add a comment |
$begingroup$
$R$ and $g_c$ each have a foot component in their units; therefore the feet cancel out when $R$ is divided by $g_c$.
$P_t$ is in pounds per square inch; since you're dividing by that, it's effectively units of square inch per pound, which is where the square inches in the answer comes from.
The rest of the unit cancellation is confusing because of the use of pounds as both a unit of mass and a unit of force (weight). This thread on thespacerace.com discusses the different ways of presenting your equation; the money quote is here:
Outside the square root, my equation uses slugs for the mass flow rate, while the other equation uses pounds (i.e. weight). To convert pounds to slugs we must divide by gc outside the square root.
Inside the square root, my equation uses R' equal to 49,720 ft-lb/slug-R, while the other equation uses 1545.32 ft-lb/lb-R. To convert ft-lb/lb-R to ft-lb/slug-R we must multiple by gc inside the square root.
The combination of these two conversion factors is,
1/gc * (gc)^1/2 = 1/gc^1/2
therefore we end up with gc in the demoninator inside the square root.
$endgroup$
$begingroup$
Nice edit, I was just going ask about that unit on gamma....
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
Zing! Yeah, I misread the unit attribution.
$endgroup$
– Russell Borogove
yesterday
$begingroup$
It's not the right pounds though outside the radical. Bad equation! Bad! (Hits equation on nose with rolled up newspaper)
$endgroup$
– Organic Marble
yesterday
$begingroup$
Ugh, flowrate being mass rather than force? Maybe I'll delete everything except the inch/foot portion of my analysis, since this is way out of my wheelhouse.
$endgroup$
– Russell Borogove
yesterday
add a comment |
$begingroup$
$R$ and $g_c$ each have a foot component in their units; therefore the feet cancel out when $R$ is divided by $g_c$.
$P_t$ is in pounds per square inch; since you're dividing by that, it's effectively units of square inch per pound, which is where the square inches in the answer comes from.
The rest of the unit cancellation is confusing because of the use of pounds as both a unit of mass and a unit of force (weight). This thread on thespacerace.com discusses the different ways of presenting your equation; the money quote is here:
Outside the square root, my equation uses slugs for the mass flow rate, while the other equation uses pounds (i.e. weight). To convert pounds to slugs we must divide by gc outside the square root.
Inside the square root, my equation uses R' equal to 49,720 ft-lb/slug-R, while the other equation uses 1545.32 ft-lb/lb-R. To convert ft-lb/lb-R to ft-lb/slug-R we must multiple by gc inside the square root.
The combination of these two conversion factors is,
1/gc * (gc)^1/2 = 1/gc^1/2
therefore we end up with gc in the demoninator inside the square root.
$endgroup$
$R$ and $g_c$ each have a foot component in their units; therefore the feet cancel out when $R$ is divided by $g_c$.
$P_t$ is in pounds per square inch; since you're dividing by that, it's effectively units of square inch per pound, which is where the square inches in the answer comes from.
The rest of the unit cancellation is confusing because of the use of pounds as both a unit of mass and a unit of force (weight). This thread on thespacerace.com discusses the different ways of presenting your equation; the money quote is here:
Outside the square root, my equation uses slugs for the mass flow rate, while the other equation uses pounds (i.e. weight). To convert pounds to slugs we must divide by gc outside the square root.
Inside the square root, my equation uses R' equal to 49,720 ft-lb/slug-R, while the other equation uses 1545.32 ft-lb/lb-R. To convert ft-lb/lb-R to ft-lb/slug-R we must multiple by gc inside the square root.
The combination of these two conversion factors is,
1/gc * (gc)^1/2 = 1/gc^1/2
therefore we end up with gc in the demoninator inside the square root.
edited yesterday
answered yesterday
Russell BorogoveRussell Borogove
87k3291376
87k3291376
$begingroup$
Nice edit, I was just going ask about that unit on gamma....
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
Zing! Yeah, I misread the unit attribution.
$endgroup$
– Russell Borogove
yesterday
$begingroup$
It's not the right pounds though outside the radical. Bad equation! Bad! (Hits equation on nose with rolled up newspaper)
$endgroup$
– Organic Marble
yesterday
$begingroup$
Ugh, flowrate being mass rather than force? Maybe I'll delete everything except the inch/foot portion of my analysis, since this is way out of my wheelhouse.
$endgroup$
– Russell Borogove
yesterday
add a comment |
$begingroup$
Nice edit, I was just going ask about that unit on gamma....
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
Zing! Yeah, I misread the unit attribution.
$endgroup$
– Russell Borogove
yesterday
$begingroup$
It's not the right pounds though outside the radical. Bad equation! Bad! (Hits equation on nose with rolled up newspaper)
$endgroup$
– Organic Marble
yesterday
$begingroup$
Ugh, flowrate being mass rather than force? Maybe I'll delete everything except the inch/foot portion of my analysis, since this is way out of my wheelhouse.
$endgroup$
– Russell Borogove
yesterday
$begingroup$
Nice edit, I was just going ask about that unit on gamma....
$endgroup$
– Organic Marble
yesterday
$begingroup$
Nice edit, I was just going ask about that unit on gamma....
$endgroup$
– Organic Marble
yesterday
1
1
$begingroup$
Zing! Yeah, I misread the unit attribution.
$endgroup$
– Russell Borogove
yesterday
$begingroup$
Zing! Yeah, I misread the unit attribution.
$endgroup$
– Russell Borogove
yesterday
$begingroup$
It's not the right pounds though outside the radical. Bad equation! Bad! (Hits equation on nose with rolled up newspaper)
$endgroup$
– Organic Marble
yesterday
$begingroup$
It's not the right pounds though outside the radical. Bad equation! Bad! (Hits equation on nose with rolled up newspaper)
$endgroup$
– Organic Marble
yesterday
$begingroup$
Ugh, flowrate being mass rather than force? Maybe I'll delete everything except the inch/foot portion of my analysis, since this is way out of my wheelhouse.
$endgroup$
– Russell Borogove
yesterday
$begingroup$
Ugh, flowrate being mass rather than force? Maybe I'll delete everything except the inch/foot portion of my analysis, since this is way out of my wheelhouse.
$endgroup$
– Russell Borogove
yesterday
add a comment |
$begingroup$
That equation as you give it with the values you supply is a bad mish-mash of units. It's painful to do this in the English system, but gather your courage, we can get through it.
You must specify the flowrate in $frac{slugs}{sec}$. Yes, slugs, the real engineer's unit of massTM. A slug is 1 $frac {lbf - sec^2} {ft}$ and equates to ~ 32.2 lbm. So flowrate in $frac{slugs}{sec}$ has the units of $frac{lbf-sec}{ft}$.
You also must specify the pressure in $frac{lbf}{ft^2}$.
Dividing through you get outside the radical the units of $ft-sec$.
Inside the radical the gas constant is $frac{ft-lbf}{slug-R}$. The R cancels out with the temperature unit. gamma is dimensionless.
So if you substitute in $frac{lbf- sec^2}{ft}$ for the slug, you end up with $frac{ft^2}{sec^2}$ inside the radical.
Taking the square root, it's $frac{ft}{sec}$, then multiply by the $ft-sec$ outside the radical, to get $ft^2$.
Welcome to the world of Apollo and Shuttle rocket engine calculations.
$endgroup$
1
$begingroup$
I was caught in the transition, my books in college had both. Shuttle and Apollo were all English, ISS is metric. Either is OK if you are used to it but metric is a lot more intuitive.
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
Are you thinking the "-" is a minus sign? It's a hyphen. It's deplorable, I know, but that's the way these units are written. See the units on the gas constant in the question. "65 ft-lb/lb R(rankine)," and in the quote in the other answer "ft-lb/lb-R to ft-lb/slug-R"
$endgroup$
– Organic Marble
10 hours ago
1
$begingroup$
oh $frac{lbftext{-}sec^2}{ft}$ what the merry heck are hyphens doing in there? "english" units are ridiculous
$endgroup$
– JCRM
10 hours ago
1
$begingroup$
I cannot argue with that, lol
$endgroup$
– Organic Marble
10 hours ago
1
$begingroup$
I think that mathjax requires text to insert a hyphen says everything about how much they belong in formulae :D
$endgroup$
– JCRM
9 hours ago
|
show 7 more comments
$begingroup$
That equation as you give it with the values you supply is a bad mish-mash of units. It's painful to do this in the English system, but gather your courage, we can get through it.
You must specify the flowrate in $frac{slugs}{sec}$. Yes, slugs, the real engineer's unit of massTM. A slug is 1 $frac {lbf - sec^2} {ft}$ and equates to ~ 32.2 lbm. So flowrate in $frac{slugs}{sec}$ has the units of $frac{lbf-sec}{ft}$.
You also must specify the pressure in $frac{lbf}{ft^2}$.
Dividing through you get outside the radical the units of $ft-sec$.
Inside the radical the gas constant is $frac{ft-lbf}{slug-R}$. The R cancels out with the temperature unit. gamma is dimensionless.
So if you substitute in $frac{lbf- sec^2}{ft}$ for the slug, you end up with $frac{ft^2}{sec^2}$ inside the radical.
Taking the square root, it's $frac{ft}{sec}$, then multiply by the $ft-sec$ outside the radical, to get $ft^2$.
Welcome to the world of Apollo and Shuttle rocket engine calculations.
$endgroup$
1
$begingroup$
I was caught in the transition, my books in college had both. Shuttle and Apollo were all English, ISS is metric. Either is OK if you are used to it but metric is a lot more intuitive.
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
Are you thinking the "-" is a minus sign? It's a hyphen. It's deplorable, I know, but that's the way these units are written. See the units on the gas constant in the question. "65 ft-lb/lb R(rankine)," and in the quote in the other answer "ft-lb/lb-R to ft-lb/slug-R"
$endgroup$
– Organic Marble
10 hours ago
1
$begingroup$
oh $frac{lbftext{-}sec^2}{ft}$ what the merry heck are hyphens doing in there? "english" units are ridiculous
$endgroup$
– JCRM
10 hours ago
1
$begingroup$
I cannot argue with that, lol
$endgroup$
– Organic Marble
10 hours ago
1
$begingroup$
I think that mathjax requires text to insert a hyphen says everything about how much they belong in formulae :D
$endgroup$
– JCRM
9 hours ago
|
show 7 more comments
$begingroup$
That equation as you give it with the values you supply is a bad mish-mash of units. It's painful to do this in the English system, but gather your courage, we can get through it.
You must specify the flowrate in $frac{slugs}{sec}$. Yes, slugs, the real engineer's unit of massTM. A slug is 1 $frac {lbf - sec^2} {ft}$ and equates to ~ 32.2 lbm. So flowrate in $frac{slugs}{sec}$ has the units of $frac{lbf-sec}{ft}$.
You also must specify the pressure in $frac{lbf}{ft^2}$.
Dividing through you get outside the radical the units of $ft-sec$.
Inside the radical the gas constant is $frac{ft-lbf}{slug-R}$. The R cancels out with the temperature unit. gamma is dimensionless.
So if you substitute in $frac{lbf- sec^2}{ft}$ for the slug, you end up with $frac{ft^2}{sec^2}$ inside the radical.
Taking the square root, it's $frac{ft}{sec}$, then multiply by the $ft-sec$ outside the radical, to get $ft^2$.
Welcome to the world of Apollo and Shuttle rocket engine calculations.
$endgroup$
That equation as you give it with the values you supply is a bad mish-mash of units. It's painful to do this in the English system, but gather your courage, we can get through it.
You must specify the flowrate in $frac{slugs}{sec}$. Yes, slugs, the real engineer's unit of massTM. A slug is 1 $frac {lbf - sec^2} {ft}$ and equates to ~ 32.2 lbm. So flowrate in $frac{slugs}{sec}$ has the units of $frac{lbf-sec}{ft}$.
You also must specify the pressure in $frac{lbf}{ft^2}$.
Dividing through you get outside the radical the units of $ft-sec$.
Inside the radical the gas constant is $frac{ft-lbf}{slug-R}$. The R cancels out with the temperature unit. gamma is dimensionless.
So if you substitute in $frac{lbf- sec^2}{ft}$ for the slug, you end up with $frac{ft^2}{sec^2}$ inside the radical.
Taking the square root, it's $frac{ft}{sec}$, then multiply by the $ft-sec$ outside the radical, to get $ft^2$.
Welcome to the world of Apollo and Shuttle rocket engine calculations.
edited yesterday
answered yesterday
Organic MarbleOrganic Marble
58.2k3159249
58.2k3159249
1
$begingroup$
I was caught in the transition, my books in college had both. Shuttle and Apollo were all English, ISS is metric. Either is OK if you are used to it but metric is a lot more intuitive.
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
Are you thinking the "-" is a minus sign? It's a hyphen. It's deplorable, I know, but that's the way these units are written. See the units on the gas constant in the question. "65 ft-lb/lb R(rankine)," and in the quote in the other answer "ft-lb/lb-R to ft-lb/slug-R"
$endgroup$
– Organic Marble
10 hours ago
1
$begingroup$
oh $frac{lbftext{-}sec^2}{ft}$ what the merry heck are hyphens doing in there? "english" units are ridiculous
$endgroup$
– JCRM
10 hours ago
1
$begingroup$
I cannot argue with that, lol
$endgroup$
– Organic Marble
10 hours ago
1
$begingroup$
I think that mathjax requires text to insert a hyphen says everything about how much they belong in formulae :D
$endgroup$
– JCRM
9 hours ago
|
show 7 more comments
1
$begingroup$
I was caught in the transition, my books in college had both. Shuttle and Apollo were all English, ISS is metric. Either is OK if you are used to it but metric is a lot more intuitive.
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
Are you thinking the "-" is a minus sign? It's a hyphen. It's deplorable, I know, but that's the way these units are written. See the units on the gas constant in the question. "65 ft-lb/lb R(rankine)," and in the quote in the other answer "ft-lb/lb-R to ft-lb/slug-R"
$endgroup$
– Organic Marble
10 hours ago
1
$begingroup$
oh $frac{lbftext{-}sec^2}{ft}$ what the merry heck are hyphens doing in there? "english" units are ridiculous
$endgroup$
– JCRM
10 hours ago
1
$begingroup$
I cannot argue with that, lol
$endgroup$
– Organic Marble
10 hours ago
1
$begingroup$
I think that mathjax requires text to insert a hyphen says everything about how much they belong in formulae :D
$endgroup$
– JCRM
9 hours ago
1
1
$begingroup$
I was caught in the transition, my books in college had both. Shuttle and Apollo were all English, ISS is metric. Either is OK if you are used to it but metric is a lot more intuitive.
$endgroup$
– Organic Marble
yesterday
$begingroup$
I was caught in the transition, my books in college had both. Shuttle and Apollo were all English, ISS is metric. Either is OK if you are used to it but metric is a lot more intuitive.
$endgroup$
– Organic Marble
yesterday
1
1
$begingroup$
Are you thinking the "-" is a minus sign? It's a hyphen. It's deplorable, I know, but that's the way these units are written. See the units on the gas constant in the question. "65 ft-lb/lb R(rankine)," and in the quote in the other answer "ft-lb/lb-R to ft-lb/slug-R"
$endgroup$
– Organic Marble
10 hours ago
$begingroup$
Are you thinking the "-" is a minus sign? It's a hyphen. It's deplorable, I know, but that's the way these units are written. See the units on the gas constant in the question. "65 ft-lb/lb R(rankine)," and in the quote in the other answer "ft-lb/lb-R to ft-lb/slug-R"
$endgroup$
– Organic Marble
10 hours ago
1
1
$begingroup$
oh $frac{lbftext{-}sec^2}{ft}$ what the merry heck are hyphens doing in there? "english" units are ridiculous
$endgroup$
– JCRM
10 hours ago
$begingroup$
oh $frac{lbftext{-}sec^2}{ft}$ what the merry heck are hyphens doing in there? "english" units are ridiculous
$endgroup$
– JCRM
10 hours ago
1
1
$begingroup$
I cannot argue with that, lol
$endgroup$
– Organic Marble
10 hours ago
$begingroup$
I cannot argue with that, lol
$endgroup$
– Organic Marble
10 hours ago
1
1
$begingroup$
I think that mathjax requires text to insert a hyphen says everything about how much they belong in formulae :D
$endgroup$
– JCRM
9 hours ago
$begingroup$
I think that mathjax requires text to insert a hyphen says everything about how much they belong in formulae :D
$endgroup$
– JCRM
9 hours ago
|
show 7 more comments
MAP3 is a new contributor. Be nice, and check out our Code of Conduct.
MAP3 is a new contributor. Be nice, and check out our Code of Conduct.
MAP3 is a new contributor. Be nice, and check out our Code of Conduct.
MAP3 is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Space Exploration Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fspace.stackexchange.com%2fquestions%2f34711%2fissue-with-units-for-a-rocket-nozzle-throat-area-problem%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
$begingroup$
You can learn more about MathJax for equations here. I removed the
rocketlab
tag; after reading that the address and original text was from circa 1967, it doesn't seem to be related to the same company that the tag refers to.$endgroup$
– uhoh
yesterday
$begingroup$
This is really a no-good equation because it has pounds mass (in the flowrate) over pounds force (in the press) outside the radical. It should be the mass flowrate in every engineer's favorite unit, slugs/sec. See Sutton p. 61 pyrobin.com/files/Rocket%20Propulsion%20Elements.pdf
$endgroup$
– Organic Marble
yesterday
$begingroup$
@OrganicMarble Are the units for $R$ supposed to be ft-lbf / lbm R?
$endgroup$
– Russell Borogove
yesterday
$begingroup$
@RussellBorogove actually no. To be consistent it should be ft-lbf / slug R engineeringtoolbox.com/…
$endgroup$
– Organic Marble
yesterday
1
$begingroup$
@OrganicMarble Same dimensions, at least.
$endgroup$
– Russell Borogove
yesterday